Well, I decided to go down to the wood shop this morning and try out the new jaws for my Nova chuck. Ive been wanting to make a small lidded box for a friend of mine, Katie, who loves to knit and is always losing her cable needles. Now cable needles are short, approximately 2" long wooden needles that are used to produce the cable effect in knitted garments like sweaters. I made her some cable needles earlier this year but she really needs a small box to keep them in as they are small and easily lost.
Discussion and Plans
Ive got some small pieces of rosewood in the shop that I thought would work well. I think this type of small turning requires a very dense and fine grained hardwood. There is a lot of small detail which has to be turned into the wood in order for the box and top to fit together tightly enough so the top doesnt slip off. So rosewood it is. The box also has to be long enough to accommodate 2" long needles and the inside diameter has to be large enough to hold at least 2 needles.
So here we go:
Here is a photo of the rosewood block. Its really short as its a pen blank. Ive marked off the ends with a white pencil and I wont turn beyond those lines as this will give me a square end to mount in the jaws in a few minutes:
These next two photos show the jaws on the Nova chuck and mounted on the lathe. The long spigots will hold the square end of the rosewood blank:
And here is the whole thing ready to go:
As this is a spindle type turning, Ive mounted the blank between centers and Im going to use my spindle gouge to rough this into a round cylinder shape:
In this photo you can see the blank. Its been turned and a tenon has been tuned into as well. The tenon will remain a part of the box end and Ill cut off the top:
And here are the parts of the box. Theyve been separated:
Next-Ive mounted the top of the box onto the lathe and hollowed out the interior. This matches precisely the diameter of the tenon on the box portion. I hand turned this and sanded smooth:
It fits!!!!
Ive taken the box portion and mounted that on the lathe and started to bore out the center with a 1/2" twist drill. I began the boring portion with a small Forstner bit but it clogged up with chips about a 1/4" inside. You can see how the chips were beginning to pack up on the twist bit too. I had to dig this out with the sharp end of a wood screw:
But eventually I got it drilled down to a depth of about 2". The top and bottom fit together very well:
Well, what a nerve wracking thing this is to make! Im going to keep this one as I dont think two needles will fit inside of it yet. Next time Ill try a longer blank as that will stay clamped inside of the jaws more securely that the short ends I used. And Ill make the whole thing longer. Lastly I will wait to true up the sides of the top and bottom until the very end and then Ill remove the waste wood and sand the ends smooth.Im going to give this another shot tomorrow.
VW
Postingan Populer
-
balsa wood projects for free Balsa wood projects for free, this… | chair...
-
As some of you know, my current shop is set up in a small 5 foot by 9 foot area that shares space with our door to the outside and the stair... -
Nothin’ fancy formed as a bluegrass band in 1994 to compete in a bluegrass competition. since then...
-
Earlier this summer I picked up a copy of Peter Follansbees video "17th Century New England Carving" and I started on a bit of a j... -
It wasnt really all that long ago, in historical terms, that average and mostly anonymous craftsman created many pieces of furniture that ar...
-
New years is the traditional chance to be reborn with new convictions that are meant to make you a better, more ideal person. While I like t... -
What a great addition to any shop! you’ll not only know the time, but also the temperature and hum...
-
Community woodworking workshop - learn to make handmade furniture, rustic furniture, and custom re...
-
Pathways to apprenticeship. there are a number of different ways to enter an apprenticeship in ont...
0 komentar:
Posting Komentar